Here is the step by step guide to configure a Huawei MA5600 Dslam, you can use a cisco console cable to access the device
* vlan numbers are optional except using vlan 1.
MA5600#config
MA5600(config)#
MA5600(config)#vlan 2 standard
MA5600(config)#vlan 15 smart
MA5600(config)#interface vlanif 2
MA5600(config-if-vlanif2)#ip address 10.10.10.2
255.255.255.252
{ <cr>|sub<K> }:
Command:
ip
address 10.10.10.2 255.255.255.252
MA5600(config-if-vlanif2)#quit
***MA5600(config)#port vlan 2 0/7 2
***MA5600(config)#port vlan 15 0/7 2
MA5600(config)#board add 0/0 ade
1[2010-01-08 18:25:38]:
A board auto disappear,FrameID:0,SlotID:0,Board_name:H565ADEF
MA5600(config)#
0 frame 0 slot board added successfully
MA5600(config)#board add 0/1 ade
1[2010-01-08 18:25:53]:
A board auto
disappear,FrameID:0,SlotID:1,Board_name:H565ADEF
MA5600(config)#
0 frame 1 slot board added successfully
MA5600(config)#adsl line-profile add 20
Start adding profile
Press 'Q' to quit the current configuration and new
configuration will be
neglected
>¡¡Do you want to name the profile (y/n) [n]:y
>¡¡Please input profile name:20
> Please choose default value type 0-adsl 1-adsl2+
(0~1) [0]:1
> Will you set basic configuration for modem? (y/n)[n]:y
Note: Setting to these mode of G992.3~5 will lead that
the adsl ports that are not support adsl2+ not be activated
ADSL transmission mode:
> 0: All (G992.1~5,T1.413)
> 1: Full rate(G992.1/3/5 or T1.413)
> 2: g.lite(G992.2/4) (ADSL over ISDN board doesn't
support g.lite mode)
> 3: T1.413(ADSL over ISDN board doesn't support T1.413
mode)
> 4: g.dmt (G992.1/3/5)
> 5: g.hs (G992.1~5, G992.5 is prior)
> 6: G992.1
> 7: G992.2
> 8: G992.3
> 9: G992.4
> 10:G992.5
> 11: ADSL all (G992.1~2,T1.413)
> 12: ADSL&ADSL2(G992.1/3 or T1.413)
Please select (0~12) [0]:0
> Trellis mode 0-disable 1-enable (0~1) [1]:1
> Downstream channel bit swap 0-disable 1-enable (0~1)
[1]:1
> Upstream channel bit swap 0-disable 1-enable (0~1)
[1]:1
> Please select channel mode 0-interleaved 1-fast (0~1)
[0]:1
>¡¡Please select form of transmit rate adaptation in
downstream:
> 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (0~2) [1]:1
> Will you set SNR margin for modem? (y/n)[n]:y
> Target SNR margin in downstream(0~15 dB) [6]:
> Minimum SNR margin in downstream (0~6 dB) [0]:
> Maximum SNR margin in downstream (6~31 dB) [31]:
> Target SNR margin in upstream (0~15 dB) [6]:
> Minimum SNR margin in upstream (0~6 dB) [0]:
> Maximum SNR margin in upstream (6~31 dB) [31]:
> Will you set parameters for rate? (y/n)[n]:y
> Minimum transmit rate in downstream (32~32000 Kbps)
[32]:64
> Maximum transmit rate in downstream (128~32000 Kbps)
[24544]:512
> Minimum transmit rate in upstream (32~6000 Kbps)
[32]:64
> Maximum transmit rate in upstream (128~6000 Kbps)
[1024]:512
Add profile 20 successfully
MA5600(config)#quit
MA5600#Display board 0
-------------------------------------------------------------------------
SlotID BoardName
Status SubType0 SubType1
-------------------------------------------------------------------------
0
ADE
Failed
1
ADE
Failed
2
3
4
5
6
7
H561SCUB
Active_normal
E4GFA
8
9
10
11
12
13
14
15
-------------------------------------------------------------------------
MA5600#display vlan 2
{ <cr>|to<K> }:
Command:
display
vlan 15
VLAN ID: 15
VLAN type: smart
VLAN attribute: common
VLAN description:
------------------------------
F/S /P Native VLAN
State
------------------------------
0/7
/2
1 down
------------------------------
Standard port number: 1
Service virtual port number: 0
MA5600#display board 0
-------------------------------------------------------------------------
SlotID BoardName
Status SubType0 SubType1
-------------------------------------------------------------------------
0
H565ADEF
Normal
1
H565ADEF
Config
2
3
4
5
6
7
H561SCUB
Active_normal
E4GFA
8
9
10
11
12
13
14
15
-------------------------------------------------------------------------
MA5600#config
MA5600(config)#interface adsl 0/0
MA5600(config-if-adsl-0/0)#deactivate all
MA5600(config-if-adsl-0/0)#
Deactivate port 0 successfully
MA5600(config-if-adsl-0/0)#
Deactivate port 1 successfully
MA5600(config-if-adsl-0/0)#
Deactivate port 2 successfully
MA5600(config-if-adsl-0/0)#
Deactivate port 3 successfully
..................
Deactivate port 62 successfully
MA5600(config-if-adsl-0/0)#
Deactivate port 63 successfully
MA5600(config-if-adsl-0/0)#activate all
profile-index 20
MA5600(config-if-adsl-0/0)#
Send the command to activate port 0 successfully
MA5600(config-if-adsl-0/0)#
Send the command to activate port 1 successfully
MA5600(config-if-adsl-0/0)#
Send the command to activate port 2 successfully
MA5600(config-if-adsl-0/0)#
Send the command to activate port 3 successfully
......................
MA5600(config-if-adsl-0/0)#
Send the command to activate port 61 successfully
MA5600(config-if-adsl-0/0)#
Send the command to activate port 62 successfully
MA5600(config-if-adsl-0/0)#
Send the command to activate port 63 successfully
MA5600(config-if-adsl-0/0)#quit
MA5600(config)#
MA5600(config)#
***MA5600(config)#multi-service-port vlan 15 board 0-1 vpi 0 vci 35 rx-cttr 5 tx-cttr 5
It will take several minutes, and console may timeout,
please use command idle-timeout to set time limit
Are you sure to create service virtual port(s)?
(y/n)[n]:y
The number of total board in this
operation:
2
The number of total service virtual port in this
operation:
128
Creating start...
16 service virtual ports have been processed
32 service virtual ports have been processed
48 service virtual ports have been processed
64 service virtual ports have been processed
80 service virtual ports have been processed
96 service virtual ports have been processed
112 service virtual ports have been processed
128 service virtual ports have been processed
Creating end:
The number of total service virtual port which need be
created: 128
The number of total service virtual port which have been
created: 128
MA5600(config)#
NATWORKER.COM(config)#ip route-static 0.0.0.0
0.0.0.0 10.10.10.1
{ <cr>|preference<K> }:
Command:
ip
route-static 0.0.0.0 0.0.0.0 10.10.10.1
MA5600(config)#quit
MA5600#
%Jan 8 18:31:40 2010 MA5600 IFNET/2/UPDOWN:Line protocol
on the interface
vlanif2 turns into UP state
state
MA5600#ping 10.10.10.1
PING 10.10.10.1: 56 data bytes, press CTRL_C to break
Reply from 10.10.10.1: bytes=56 Sequence=0 ttl=254 time =
4 ms
Reply from 10.10.10.1: bytes=56 Sequence=1 ttl=254 time =
2 ms
Reply from 10.10.10.1: bytes=56 Sequence=2 ttl=254 time =
2 ms
Reply from 10.10.10.1: bytes=56 Sequence=3 ttl=254 time =
2 ms
Reply from 10.10.10.1: bytes=56 Sequence=4 ttl=254 time =
2 ms
--- 10.10.10.1 Ping statistics ---
5 packets transmitted
5 packets received
0.00% packet loss
Round-trip min/avg/max = 2/2/4 ms
MA5600#display vlan 15
{ <cr>|to<K> }:
Command:
display
vlan 15
VLAN ID: 15
VLAN type: smart
VLAN attribute: common
VLAN description:
------------------------------
F/S /P Native VLAN
State
------------------------------
0/7
/2
1 up
------------------------------
Standard port number: 1
---------------------------------------------------
Type State F/ S/ P VPI
VCI FLOWTYPE FLOWPARA
---------------------------------------------------
adl act/up 0/ 0/ 0
0 35
- -
adl act/up 0/ 0/ 1
0 35
- -
adl act/up 0/ 0/ 2 0
35 -
-
adl act/up 0/ 0/ 3
0 35
- -
adl act/up 0/ 0/ 4
0 35
- -
adl act/up 0/ 0/ 5
0 35
- -
adl act/up 0/ 0/ 6
0 35
- -
---- More ( Press 'Q' to break )
----[37D
[37D[1A
....................................
---- More ( Press 'Q' to break )
----[37D
[37D[1A
adl act/up 0/ 1/39
0 35 -
-
adl act/up 0/ 1/40
0 35
- -
adl act/up 0/ 1/41
0 35
- -
adl act/up 0/ 1/42
0 35
- -
adl act/up 0/ 1/43
0 35
- -
adl act/up 0/ 1/44
0 35
- -
adl act/up 0/ 1/45
0 35
- -
adl act/up 0/ 1/46
0 35
- -
adl act/up 0/ 1/47
0 35
- -
adl act/up 0/ 1/48
0 35
- -
adl act/up 0/ 1/49
0 35
- -
adl act/up 0/ 1/50
0 35
- -
adl act/up 0/ 1/51
0 35
- -
adl act/up 0/ 1/52
0 35
- -
adl act/up 0/ 1/53
0 35 -
-
adl act/up 0/ 1/54
0 35
- -
adl act/up 0/ 1/55
0 35
- -
adl act/up 0/ 1/56
0 35
- -
adl act/up 0/ 1/57
0 35
- -
adl act/up 0/ 1/58
0 35
- -
adl act/up 0/ 1/59
0 35
- -
adl act/up 0/ 1/60
0 35
- -
adl act/up 0/ 1/61
0 35
- -
adl act/up 0/ 1/62
0 35
- -
---- More ( Press 'Q' to break )
----[37D
[37D[1A
adl act/up 0/ 1/63
0 35
- -
---------------------------------------------------
Service virtual port number: 128
Note: F--Frame, S--Slot, P--Port(or virtual port, such as
IMA group etc.)
The characters precede / in the STATE column indicate the
Admin-Status
and characters behind the / indicate the Oper-Status of
the service-port
. act means activate and deact means deactivate, dn is
abbreviation of
down.
MA5600#config
MA5600(config)#sysname natworker.com
NATWORKER.COM(config)#quit
NATWORKER.COM#save
{ <cr>|configuration<K>|data<K> }:
Command:
save
NATWORKER.COM#
It will take several minutes to save configuration file,
please wait...
NATWORKER.COM#
Configuration file had been saved successfully
Note: The configuration file will take effect after being
activated
NATWORKER.COM#
The data is being saved, please wait a moment...
NATWORKER.COM#save
NATWORKER.COM#save data
Failure: System is busy, please retry after a while
NATWORKER.COM#
1[2010-01-08 18:34:29]:The percentage of saved data on 7
slot's main control board is: 21%
NATWORKER.COM#
1[2010-01-08 18:34:32]:The percentage of saved data on 7
slot's main control board is: 27%
NATWORKER.COM#
1[2010-01-08 18:35:01]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#save
{ <cr>|configuration<K>|data<K> }:
1[2010-01-08 18:35:04]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#save
Command:
save
Failure: System is busy, please retry after a while
NATWORKER.COM#
1[2010-01-08 18:35:07]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#
1[2010-01-08 18:35:10]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#save data [1D[1C
Failure: System is busy, please retry after a while
NATWORKER.COM#
1[2010-01-08 18:35:13]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#
1[2010-01-08 18:35:16]:The percentage of saved data on 7
slot's main control board is: 98%
NATWORKER.COM#
NATWORKER.COM#
1[2010-01-08 18:35:17]:The data of 7 slot's main control
board is saved
completely
NATWORKER.COM#
No comments:
Post a Comment